MENG Aerospace Engineering (AERU10) FT

2021 - 2022

For students whose initial registration was in 2020-21 or earlier

Year 1

Core These are a compulsory part of your degree: you cannot change them. units (120 credits)

A student will take

Semester 1
FCE1001	Global Engineering Challenge Week	AUT SEM	0 credits
Full academic year
ACS1321 XCannot be taken with: ACS132 + EMPTY.	Introduction to Systems Analysis and Control	ACAD YR	15 credits
AER104 P⇒Is a pre-requisite for: AER284 AER291 (when the module is running)	Engineering Statics and Dynamics	ACAD YR	15 credits
AER11001 P⇒Is a pre-requisite for: AER298 (when the module is running)	Aerospace Aerodynamics and Thermodynamics	ACAD YR	15 credits
AER11002	Aerospace Engineering Design, Build and Test	ACAD YR	20 credits
AER11004 XCannot be taken with: BIE2643 MAT1643	Introduction to Aerospace Materials	ACAD YR	20 credits
AER11005	Introduction to Aerospace Electrical and Electronic Circuits	ACAD YR	15 credits
MAS156 P⇒Is a pre-requisite for: AER201 MAS241 MAS381 (when the module is running) + Unrestricted - only subject to availability. This module is for students in EEE and Aerospace Engineering..	Mathematics (Electrical)	ACAD YR	20 credits

Year 2

Core These are a compulsory part of your degree: you cannot change them. units (60 credits)

A student will take

Semester 1
AER201 ⇐PPre-requisites: MAS156 XCannot be taken with: MAS241 + This module is for students in Aerospace Engineering..	Mathematics for Aerospace Engineers	AUT SEM	10 credits
AER284 ⇐P⇒Pre-requisites: AER104 Is a pre-requisite for: AER380 (when the module is running)	Aerostructures	AUT SEM	10 credits
FCE2001 + Yes. Restricted to second year Faculty of Engineering students.	Engineering - You're Hired	AUT SEM	0 credits
Semester 2
AER21003	Group Design, Build and Test: Air Systems Development	SPR SEM	10 credits
AER298 ⇐P⇒Pre-requisites: AER11001 Is a pre-requisite for: AER380 (when the module is running)	Aerospace Fluids Engineering	SPR SEM	10 credits
Full academic year
ACS230 ⇐P⇒Pre-requisites: ACS132 Is a pre-requisite for: ACS317 (when the module is running)	Control Systems Design and Analysis	ACAD YR	20 credits

One of the following streams

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (60 credits)

AEROMECHANICS STREAM

A student will take 60 credits from this group.

Semester 1
AER293	Applied Aerospace Heat Transfer	AUT SEM	10 credits
COM161 + Not open to students from the Department of Computer Science or students who are taking or have taken COM160. .	Introduction to Programming and Problem Solving	AUT SEM	10 credits
MAT2730 XCannot be taken with: MEC207 + Restricted to students registered on Aerospace Engineering programmes..	Selection and Processing of Aerospace Materials	AUT SEM	10 credits
Semester 2
AER2350 XCannot be taken with: MAT2350 MAT6327	Materials Selection and Fracture Mechanics	SPR SEM	10 credits
AER291 ⇐PPre-requisites: AER104	Dynamics of Aerospace Structures and Machines	SPR SEM	10 credits
MEC209 P⇒Is a pre-requisite for: MEC330 MEC333 (when the module is running) + Restricted to students studying in the Dept of Mechanical Engineering and the Inter-disciplinary Programmes office.	Design of Structures, Machines and Systems	SPR SEM	10 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (60 credits)

AVIONIC SYSTEMS STREAM

A student will take 60 credits from this group.

Full academic year
ACS130	Introduction to Systems Engineering & Software	ACAD YR	20 credits
ACS232	Signals, Systems, and Communications	ACAD YR	20 credits
EEE223	Electrical Energy Management and Conversion	ACAD YR	20 credits

Students commencing Level 1 of a programme of study must take FCE1001 Faculty Global Engineering Challenge Week as a core module. A student will be expected to pass the module in order to progress to Level 3. A student must pass the module in order to graduate.

Students commencing Level 2 of a programme of study must take FCE2001 Engineering - You're Hired as a core module. A student will be expected to pass the module in order to progress to Level 3. A student must pass the module in order to graduate.

Year 3

Core These are a compulsory part of your degree: you cannot change them. units (80 credits)

A student will take

Semester 1
AER301	Aerospace Group Design Project: Design	AUT SEM	10 credits
AER325	Aerodynamic Design	AUT SEM	10 credits
AER380 ⇐PPre-requisites: AER284 AER298 CCo-requisites: AER302 + This unit is only available to students on Aerospace Engineering courses..	Aircraft Design	AUT SEM	10 credits
MGT388	Finance and Law for Engineers	AUT SEM	10 credits
Semester 2
AER302 CCo-requisites: AER301 AER380	Aerospace Group Design Project: Build and Test	SPR SEM	10 credits
AER324	Aircraft Dynamics and Control	SPR SEM	10 credits
AER345 P⇒Is a pre-requisite for: AER410 (when the module is running)	Aero Propulsion	SPR SEM	10 credits
MEC328 + Restricted to students within the Faculty of Engineering..	Managing Engineering Projects and Teams	SPR SEM	10 credits

One of the following streams

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (10 credits)

AEROMECHANICS STREAM

A student will take 10 credits from this group.

Semester 2
MEC327 P⇒Is a pre-requisite for: MEC453 (when the module is running) + Restricted to students within the Faculty of Engineering..	Structural Vibration	SPR SEM	10 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (20 credits)

A student will take 20 credits from this group.

Semester 1
ACS327	Space Systems Engineering	AUT SEM	10 credits
AER330 XCannot be taken with: MAT333 MAT630 MAT630	Aerospace Metals	AUT SEM	10 credits
MAT306 XCannot be taken with: MAT6430	Composite Materials and Micromechanics	AUT SEM	10 credits
MEC303 + Restricted to students registered for a Programme of Study within the Faculty of Engineering.	Advanced Engineering Thermodynamic Cycles	AUT SEM	10 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (10 credits)

A student will take 10 credits from this group.

Semester 2
MEC313 P⇒Is a pre-requisite for: MEC457 MEC457 MEC6440 (when the module is running) + Restricted to students registered for a programme of study within the Faculty of Engineering.	Finite Element Techniques	SPR SEM	10 credits
MEC320 P⇒Is a pre-requisite for: MEC458 MEC467 (when the module is running) + Only availabe to students registered for a Programme of Study within Mechanical Engineering or IPO.	Computational Fluid Dynamics	SPR SEM	10 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (20 credits)

AVIONICS STREAM

A student will take 20 credits from this group.

Semester 1
ACS327	Space Systems Engineering	AUT SEM	10 credits
Semester 2
ACS321	Digital Signal Processing	SPR SEM	10 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (20 credits)

A student will take 20 credits from this group.

Semester 1
ACS317 ⇐P⇒Pre-requisites: ACS132 ACS230 ACS234 Is a pre-requisite for: ACS336 ACS61015 ACS6116 (when the module is running)	State-Space Control Design	AUT SEM	10 credits
Semester 2
ACS336 ⇐PPre-requisites: ACS317 XCannot be taken with: ACS61015	Hardware-in-the-Loop & Rapid Control Prototyping	SPR SEM	10 credits
ACS337	Robotic Systems	SPR SEM	10 credits
EEE334 XCannot be taken with: EEE317	Antennas, Radar and Navigation	SPR SEM	10 credits
Full academic year
EEE224 P⇒Is a pre-requisite for: ACS342 (when the module is running)	Communication Electronics	ACAD YR	20 credits

During Level 3, a student must attain a satisfactory standard in a Flight Laboratory Course, the arrangements being subject to the approval of the Aerospace Engineering Board of Studies.

Year 4

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (45 credits)

A student will take 45 credits from this group.

Full academic year
ACS429	Aerospace Individual Investigative Project	ACAD YR	45 credits
AER429 + Restricted to students registered on Aerospace Engineering programmes.	Aerospace Individual Investigative Project	ACAD YR	45 credits
COM429	Aerospace Individual Investigative Project	ACAD YR	45 credits
EEE429 + Restricted to students registered on Aerospace Engineering programmes.	Aerospace Individual Investigative Project	ACAD YR	45 credits
MAT429 + Restricted to students registered on Aerospace Engineering programmes.	Aerospace Individual Investigative Project	ACAD YR	45 credits
MEC429 + Restricted to students registered on Aerospace Engineering programmes.	Aerospace Individual Investigative Project	ACAD YR	45 credits

One of the following streams

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (15 credits)

AEROMECHANICS STREAM

A student will take 15 credits from this group.

Semester 2
MEC462 + Restricted to Level 7 or above students registered on a programme in the Faculty of Engineering..	Aviation Safety and Aeroelasticity	SPR SEM	15 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (45 credits)

A student will take 45 credits from this group.

Semester 1
ACS6126	Advanced Space Systems and Space Weather	AUT SEM	15 credits
AER61005	Industrial Training Programme: Aerospace Materials and Manufacturing	AUT SEM	15 credits
MEC445 + Restricted to associated programmes..	Industrial Applications of Finite Element Analysis	AUT SEM	15 credits
MEC449 + Restricted to Level 7 or above students registered on a programme in the Faculty of Engineering..	Advanced Engineering Fluid Dynamics	AUT SEM	15 credits
MEC452 + Restricted to Level 7 or above students registered on a programme in the Faculty of Engineering..	Advanced Dynamics	AUT SEM	15 credits
MEC463 + Restricted to Level 7 or above students registered on a programme in the Faculty of Engineering..	Advanced Aerospace Propulsion Technology	AUT SEM	15 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (15 credits)

A student will take 15 credits from this group.

Semester 2
MAT6104 CCo-requisites: MAT6430 XCannot be taken with: AER476	Design and Manufacture of Composites	SPR SEM	15 credits
MAT6334 XCannot be taken with: MAT6374	Advanced Materials Manufacturing: Part I	SPR SEM	15 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (30 credits)

AVIONICS STREAM

A student will take 30 credits from this group.

Semester 1
ACS6126	Advanced Space Systems and Space Weather	AUT SEM	15 credits
ACS6127	Real-Time Embedded System	AUT SEM	15 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (15 credits)

A student will take 15 credits from this group.

Semester 1
ACS61015 ⇐PPre-requisites: ACS317 XCannot be taken with: ACS336	Rapid Control Prototyping	AUT SEM	15 credits
COM4506 + Students taking this module are expected to have done a programming module such as COM160 or have completed a first year in the Computer Science Department. The language used in COM4506 assignment is Java hence prior familiarity with it is necessary..	Testing and verification in safety-critical systems	AUT SEM	15 credits
Full academic year
EEE6203	Motion Control and Servo Drives	ACAD YR	15 credits
EEE6220	Electronic Communication Technologies	ACAD YR	15 credits
EEE6221	Data Coding Techniques for Communication and Storage	ACAD YR	15 credits
EEE6222	Principles of Communications	ACAD YR	15 credits

AND

Approved These are on a restricted list of modules offered by your department(s). Normally you will need to select a minimum number of credits from the list. units (30 credits)

A student will take 30 credits from this group.

Semester 2
ACS402	Industrial training programme (ITP) in Avionics	SPR SEM	15 credits
ACS6116 ⇐PPre-requisites: ACS317	Advanced Control	SPR SEM	15 credits
ACS6121 XCannot be taken with: COM3009	Mobile Robotics and Autonomous Systems	SPR SEM	15 credits
ACS6124	Multisensor and Decision Systems	SPR SEM	15 credits

A student must pass the Aerospace Individual Investigative Project (ACS429 / COM429 / EEE429 / MAT429 / MEC429) at the first attempt in order to be eligible for the award of the Degree of MEng Aerospace Engineering. A student who fails to satisfy this requirement may be permitted by the Faculty to become instead a student for the Degree of BEng Aerospace Engineering (AERU11).

A student must pass security clearance in order to take ACS402 Industrial Training Programme: Avionics. A student who fails to pass security clearance will be permitted to take a suitable replacement module at the discretion of the Aerospace Course Director.

A student must satisfy the requirements of the General Regulations for First Degrees as to progression in order to continue as a student for the Degree of MEng Aerospace Engineering (AERU10). A student who fails to satisfy these requirements may be permitted by the Faculty to (a) at the end of Level 2 become a candidate for the Degree of BEng Aerospace Engineering (AERU11), or (b) at the end of Level 3 become a candidate for the unaccredited Degree of BEng Aerospace Technology (AERU17). A student who fails the Individual Advanced Project at Level 4 or who chooses to withdraw from the University at the end of Level 3 may be awarded the unaccredited Degree of BEng Aerospace Technology (AERU17).

⇐P	-	This module has pre-requisite(s).
P⇒	-	This module is a pre-requisite for other modules.
C	-	This module has co-requisite(s).
X	-	Some modules cannot be studied in combination with this module.
+	-	Additional information about requirements for studying this module.

Please note that the regulations displayed on this page reflect provision in 2021/22 and may not reflect study undertaken in other academic sessions. To see regulations that applied in another academic session, please return to the Programme Regulations Finder home screen and select the appropriate session.