Mr M. Mirza Abdillah Pratama (he/him)

Department of Civil and Structural Engineering

Research Student

mpratama1@sheffield.ac.uk

D120, Sir Frederick Mappin Building (Broad Lane Building)

Full contact details

Mr M. Mirza Abdillah Pratama
Department of Civil and Structural Engineering
D120
Sir Frederick Mappin Building (Broad Lane Building)
Mappin Street
Sheffield
S1 3JD

Profile: M. Mirza Abdillah Pratama (Mirza) earned his B.Eng. degree from Diponegoro University, Indonesia in 2014 and a M.Eng. in Structural Engineering from Diponegoro University, Indonesia in 2015. He joined as a lecturer at Department of Civil Engineering and Planning, Faculty of Engineering, State University of Malang (Universitas Negeri Malang), Indonesia from 2016 until present. His research mainly concerns concrete materials, and also finite element modelling. He focuses the research on graded concrete and its prospective development. During his career, he joined non-degree training in Delft University of Technology (2019), Oregon Institute of Technology (2021), and the University of Sheffield (2022). He hold a professional degree in civil engineering (Engineer) from Brawijaya University in 2022. Currently, he is working as a PhD student in Civil and Structural Engineering at the University of Sheffield, the United Kingdom.

Research interests

Research Project: Performance of 3D printed concrete under demanding conditions

Supervisor: Dr Behzad Nematollahi, Dr Giacomo Torelli

Additive construction technology (ACT) can allow the free-form construction of concrete structures with complex geometries without the use of expensive and waste-generating formwork. In addition, the ACT could decrease the number of injuries and deaths in the construction industry by replacing dangerous low-skilled construction work with safer high-skilled work. However, there are challenges to be overcome before 3DCP can be routinely implemented in the construction sector. For example, no study is available on the performance of additively manufactured concrete under multiaxial stresses. In addition, there are very limited studies on the performance of additively manufactured concrete under elevated temperatures. This project aims to fill these knowledge gaps by investigating the performance of additively manufactured concrete members under multiaxial stresses and elevated temperatures. This project is expected to facilitate the adoption of the ACT in the construction industry.

Publications

Journal articles

Aylie H, Gan BS, As'ad S & Pratama MMA (2015) Parametric study of the load carrying capacity of functionally graded concrete of flexural members. International Journal of Engineering and Technology Innovation, 5(4), 233-241.
Han A, Gan BS & Pratama MMA () Effects of Graded Concrete on Compressive Strengths. International Journal of Technology, 7(5), 732-732.

Conference proceedings papers

Pradhana RA, Pratama MMA, Santoso E & Karjanto A (2019) Structural performance of multi-storey building using flat slab and conventional slab to seismic loads (Case study: Faculty building of Sport Science in Universitas Negeri Malang, Indonesia). IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012053-012053)
Nindyawati N, Sulton M, Pratama MMA & Rahayuningsih T (2019) Confinements of concrete cylinders using bamboo spiral stirrups. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012059-012059)
Damayanthi W, Novitasari Y & Pratama MMA (2019) Effects of segregation on reinforced concrete column, a numerical approach. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012061-012061)
Pratama MMA, Arifanda W, Karyadi K, Nindyawati N, Sulaksitaningrum R & Prayuda H (2019) Numerical and experimental investigation on the shear resistance of functionally graded concrete (FGC) beams. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012055-012055)
Gan BS, Kiryu S, Han A & Pratama MMA (2019) Economic prospects of Steel Reinforced Functionally Graded Concrete (SRFGC) beam structures. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012001-012001)
Pratama MMA, Vertian T, Umniati BS & Yoh WH (2019) Flexural behaviour of the functionally graded concrete beams using two-layers and three-layers configuration. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012054-012054)
Umniati BS, Sulton M, Pratama MMA, Mahendra AG & Prameswara AP (2019) Studies on Flexure Characteristics of Bamboo-Reinforced Concrete as an Element of Triple Friction Pendulum Damper. IOP Conference Series: Earth and Environmental Science, Vol. 366(1) (pp 012023-012023)
Sulaksitaningrum R, Umniati BS, Ellsa Sarassantika IP, Casita CB, Pratama MMA, Santoso E & Sulton M (2019) The optimal damper placement configuration for three-dimensional RC building. IOP Conference Series: Materials Science and Engineering, Vol. 669(1) (pp 012056-012056)
Saleh F, Prayuda H, Monika F & Pratama MMA (2019) Characteristics Comparison on Mechanical Properties of Mortars using Agriculture Waste as a Cement Replacement Materials. IOP Conference Series: Materials Science and Engineering, Vol. 650(1) (pp 012039-012039)
Putra ABNR, Ihwanudin M, Mindarta EK, Puspitasari P & Pratama MMA (2018) Occupational Health And Safety (OHS) management for employees on the risk of diseases due to the intensity of computer use in the workplace/industry. MATEC Web of Conferences, Vol. 204 (pp 01016-01016)
Pratama MMA, Pratiwi YD, ’Ilmi MA & Mahardika A (2018) GECOBRIDGE: A concept of a smart eco-friendly integrated bridge utilizing geopolymer and graded concrete technology. MATEC Web of Conferences, Vol. 204 (pp 06005-06005)
Zhabrinna , Davies RJ, Pratama MMA & Yusuf M (2018) BIM adoption towards the sustainability of construction industry in Indonesia. MATEC Web of Conferences, Vol. 195 (pp 06003-06003)
Pratama MMA, Umniati BS, Prasiwi G, Han AL, Sthenly Gan B, Risdanareni P & Zhabrinna Z (2018) Effect of monotonic lateral load on the performance of reinforced graded concrete column, an experimental study. MATEC Web of Conferences, Vol. 195 (pp 02022-02022)
Zhabrinna & Pratama MMA (2018) The implementation of sustainable concept in waste management through project life cycle process in Gold Coast. MATEC Web of Conferences, Vol. 195 (pp 06001-06001)
Pratama MMA, Umniati BS, Arumsari Mutiara Wulandari B, Han AL, Sthenly Gan B & Zhabrinna Z (2018) Modulus elasticity of the graded concrete, a preliminary research. MATEC Web of Conferences, Vol. 195 (pp 01005-01005)
Ahmar AS, Hidayat R, Busro , Abdullah D, Rahim R, Abraham J, Kurniasih N, Irawan DE, Sutiksno DU, Napitupulu D , Setiawan MI et al (2018) Lecturers’ Understanding on Indexing Databases of SINTA, DOAJ, Google Scholar, SCOPUS, and Web of Science: A Study of Indonesians. Journal of Physics: Conference Series, Vol. 954 (pp 012026-012026)
Pratama MMA, Aylie H, Gan BS, Umniati BS, Risdanareni P & Fauziyah S (2017) Effect of concrete strength gradation to the compressive strength of graded concrete, a numerical approach. AIP Conference Proceedings
Gan BS, Aylie H & Pratama MMA (2015) The Behavior of Graded Concrete, an Experimental Study. Procedia Engineering, Vol. 125 (pp 885-891)
Sulistyana , Purwanto , Widoanindyawati V & Pratama MMA (2014) The Influence of Compression Applied during Production to the Compression Strength of Dry Concrete: An Experimental Study. Procedia Engineering, Vol. 95 (pp 465-472)
Puspitasari P, Alifian C, Aripriharta , Razak JA & Pratama MMA () Corrosion Resistance Analysis of ST37 Carbon Steel Material Using Phosphate Conversion Coating in Various Immersion Durations. Key Engineering Materials, Vol. 851 (pp 61-67)
Pratama MMA, Suhud RK, Puspitasari P, Kusuma FI & Rahma Putra ABN () Finite element analysis of the bending moment-curvature of the double-layered graded concrete beam. IOP Conference Series: Materials Science and Engineering, Vol. 494 (pp 012064-012064)

Research group: Structural Engineering & Materials